manualshive.com logo in svg

RACOM RAy3-11, Руководство пользователя, Страница: 151 / 241

Поделиться
Скачать
RACOM RAy3-11 Скачать руководство пользователя страница 151

Factory settings (Local)

Applying Factory settings to Local unit. Using the factory settings function will revert the unit to its ori-
ginal state - like it was shipped from the factory.

Loc

Peer

o

 Link

o

 Switch

o

 User

Restore factory settings

Applying Factory settings to Local unit. The unit reboots itself after applying all changes.

Warning

All configuration items, user accounts, SW keys, measured values and system messages
(logs) will be irreversibly deleted. This task takes a few minutes to complete. Do not interrupt
the power supply during the operation.

Diagnostic package (Local & Peer)

To facilitate communication with the technical support you can create an archive file with detailed in-
formation about the unit. If connection with Peer unit is active the diagnostic information from both units
are saved.

Create & download file

Saving a file with information about the unit (Local and Peer).

Note

This task takes a few minutes to complete.

Management Information Base

Management Information Base (called often a MIB table) is a key info for setting up a SNMP commu-
nication between the unit and a network management system (NMS).

SNMP MIB

Saving a file with SNMP MIB (Management Information Base) table. The downloaded file is
identical to the SNMP MIB table file downloaded from RACOM web (

section Downloads

2

) for relevant

FW version.

2

https://www.racom.eu/download/hw/ray/free/eng/03b_fw/ray3-mib.mib

151

© RACOM s.r.o. – RAy3 Microwave Link

Configuration

Содержание RAy3-11


















































































































































































































































Отзывы:

Нет отзывов