Quorum Q150T S Скачать руководство пользователя страница 79

Страница: 79 / 92

Q150T Sample Preparation System

Q150T - Instruction Manual

10473 - Issue 5

Table 25

Carbon Pulse/Rod Evaporation profile parameters

Name

Default

Value

Minimum
Value

Maximum
Value

Comment

Material

Carbon

Fixed; read only parameter

Pulse current (A)

60 (cord)
75 (rod)

120

Current applied to cord during
the evaporation pulse

Max Pulse
Voltage (V)*

20 (cord)
10 (rod)

The voltage across the cord is
limited to this value during the
evaporation pulse

Pulses Length (s)

0.02

Time is second that the pulse is
applied for

Number of pulses

Number of consecutive pulse
cycles

Pulse interval (s)

The time between the start of
consecutive pulse cycles. Must
exceed pulse length.

Outgas time (s)

Time cord or rod is outgassed
before pulse cycle(s).

Outgas current
(A)

30 (cord)
20 (rod)

Current applied at the start of
outgas step.

Max Outgas
current (A)

Maximum current permitted
during outgas.

Max Outgas
voltage (V)

Maximum voltage permitted
during outgas

Outgas source*

Yes

Include or exclude outgassing
step

Tooling factor

0.1

Tooling factor for this process

Pump hold*

Yes

Yes,

Q150T pumps down to

outgas-ready state and waits for
user input.

Note:

If hold time (set in

System | Vacuum | Pump hold
time

– see page 46 is

exceeded, Q150T vents
chamber.

Flush chamber*

Yes

Set to

Yes

to flush chamber

with nitrogen before pumping
down.

* Admin group level required to edit this property

Содержание Q150T S





























































































Результаты поиска

Содержание Q150T S

Отзывы:

Quorum Q150T S, Инструкция по эксплуатации, Страница: 79 / 92

Результаты поиска

Содержание Q150T S

Отзывы: