manualshive.com logo in svg

Quorum Q150T E, Инструкция по эксплуатации

Поделиться
Скачать
Quorum Q150T E Скачать руководство пользователя страница 15

Q150T Sample Preparation System

Q150T - Instruction Manual

15

10473 - Issue 5

2.3.4

Vacuum Connections

1.

If  you  are using  an  existing  or  alternative  vacuum  pump,  and  have  any  difficulty 
with connections, please ask for advice.  

2.

If  the  instrument  is  NOT  going  to  be  vented  into  an  extraction  system,  fit  an  Oil 
Mist  Filter  with  metal  adapter  to  the  outlet  of  the  vacuum  pump.  Please  refer  to 
the manufacturer’s instructions.

3.

Ensure that the vacuum pump is filled with the correct oil. 

4.

If  the  vacuum  pump  is  fitted with an on/off switch, ensure that it is set to the 'on' 
position to allow the instrument to control its power supply.

5.

Connect  the  flexible  vacuum  hose  to  the  spigot on the rear panel using the hose 
clip  provided. This  is  a  push-on  fit  to  the  Instrument.  Ensure  that  this  is  firmly  in 
place to the full length of the spigot.

A  rotating  vacuum  spigot is  available  for  more  convenient  hose 
connection  in  installations where the instrument is to be located close 
to a back wall (see page 69).

Содержание Q150T E





























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды