manualshive.com logo in svg

Quonset Microwave QM1013-101, Руководство пользователя, Страница: 85 / 94

Поделиться
Скачать
Quonset Microwave QM1013-101 Скачать руководство пользователя страница 85

0.001-6 GHz Single Channel Upconverter

IEEE 488.2 Command Reference

6.10 *SDS

<

NRf

>

The

*SDS

(Save Default device Settings) command restores the specified state of the QM1013-101

0.001-6 GHz Single Channel Upconverter to the default state settings. There are 5 re-writeable memory
locations, specified by choosing an index between 1 and 5. The parameters restored are the

RF Power

State, External LO1 Enabled, External LO1 Switch Override, External LO2 Enabled, External LO2 Switch
Override, External Reference Enabled, External Referece Switch Override, Tune Frequency, Attenuator
1 Setting, Attenuator 2 Setting, and Attenuator 3 Setting

. For a detailed description of the parameters

saved, see the relevent command descriptions in this manual. Issuing this command does not change
the current settings. NOTE: The MEM_CLR button on the back panel will rewrite the contents of states
1-5 with the contents of state 0 when depressed, serving as a reset to factory defaults.

Syntax

*

SDS

Space

NRf

Allowed Values

The

NRf

parameter can be any integer in the range of 1 to 5.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 1 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.0.1

74

Содержание QM1013-101































































































Отзывы:

Нет отзывов