manualshive.com logo in svg

Quonset Microwave QM1013-101, Руководство пользователя, Страница: 84 / 94

Поделиться
Скачать
Quonset Microwave QM1013-101 Скачать руководство пользователя страница 84

0.001-6 GHz Single Channel Upconverter

IEEE 488.2 Command Reference

6.9 *SAV

<

NRf

>

The

*SAV

(SAVe) command saves the current setup to non-volatile memory. There are 5 re-writeable

memory locations, specified by choosing an index between 1 and 5. Any of the 5 states can be re-
stored on startup when specified with the SYSTem:BOOTstate command. The parameters saved are the

RF Power State, External LO1 Enabled, External LO1 Switch Override, External LO2 Enabled, External
LO2 Switch Override, External Reference Enabled, External Referece Switch Override, Tune Frequency,
Attenuator 1 Setting, Attenuator 2 Setting, and Attenuator 3 Setting

. For a detailed description of the

parameters saved, see the relevent command descriptions in this manual. NOTE: The MEM_CLR button
on the back panel will rewrite the contents of states 1-5 with the contents of state 0 when depressed,
serving as a reset to factory defaults.

Syntax

*

SAV

Space

NRf

Allowed Values

The

NRf

parameter can be any integer in the range of 1 to 5.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 1 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.0.1

73

Содержание QM1013-101































































































Отзывы:

Нет отзывов