Quonset Microwave QM1013-101 Скачать руководство пользователя страница 82

Страница: 82 / 94

0.001-6 GHz Single Channel Upconverter

IEEE 488.2 Command Reference

6.7 *RCL

NRf

The

*RCL

(ReCaLl) command restores a previously saved state from non-volatile memory. In addition to

factory default state 0, there are 5 re-writeable memory locations, specified by choosing an index between
1 and 5. The restored parameters are the

RF Power State, External LO1 Enabled, External LO1 Switch

Override, External LO2 Enabled, External LO2 Switch Override, External Reference Enabled, External
Referece Switch Override, Tune Frequency, Attenuator 1 Setting, Attenuator 2 Setting, and Attenuator 3
Setting

. For a detailed description of the parameters saved, see the relevent command descriptions in

this manual. When the *RCL command is called, these parameters will be applied to the device.

Syntax

RCL

Space

NRf

Allowed Values

The

NRf

parameter can be any integer in the range of 0 to 5.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 0 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.0.1

Содержание QM1013-101































































































Результаты поиска

Содержание QM1013-101

Отзывы:

Quonset Microwave QM1013-101, Руководство пользователя, Страница: 82 / 94

Результаты поиска

Содержание QM1013-101

Отзывы: