Quonset Microwave QM1013-101 Скачать руководство пользователя страница 41

Страница: 41 / 94

QM1013-101 0.001-6 GHz Single Channel Upconverter

User Manual

1.2 FREQuency Subsystem

Table 4.2:

FREQuency Subsystem Commands Summary

Command

Page

Description

FREQuency:LOCK

Returns the lock status of the internal LOs.

FREQuency:TUNE

Sets or Returns the desired tuning frequency in GHz.

FREQuency:TUNErACTual

Returns the actual tuning frequency of the device in
GHz. This query is useful when internal frequency
rounding occurs in integer mode.

FREQuency:LO1:EXTernal

Sets or Returns internal/external status of the LO1 os-
cillator.

FREQuency:LO1:LOCK

Returns the lock status of the internal LO1s for both
channels.

FREQuency:LO2:EXTernal

Sets or Returns internal/external status of the LO2 os-
cillator.

FREQuency:LO2:LOCK

Returns the lock status of the internal LO2 for the sys-
tem.

FREQuency:REFerence:EXTernal

Sets or Returns whether the internal or external sup-
plied reference oscillator is used.

1.3 POWEr Subsystem

Table 4.3:

POWEr Subsystem Commands Summary

Command

Page

Description

POWEr:AT1

Sets or Returns the value of first upconverter attenua-
tor.

POWEr:AT2

Sets or Returns the value of second upconverter at-
tenuator.

POWEr:AT3

Sets or Returns the value of third upconverter attenu-
ator.

POWEr:RF

Turns on or off the RF output of the device.

1.4 STATus Subsystem

Quonset Microwave

Revision 1.0.1

Содержание QM1013-101































































































Результаты поиска

Содержание QM1013-101

Отзывы:

Quonset Microwave QM1013-101, Руководство пользователя, Страница: 41 / 94

Результаты поиска

Содержание QM1013-101

Отзывы: