Quonset Microwave QM1004-0.5-18 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 105

Quonset Microwave QM1004-0.5-18 Скачать руководство пользователя страница 95

Combined RF Upconverter/Downconverter

IEEE 488.2 Command Reference

6.9 *SAV

<

NRf

>

The

*SAV

(SAVe) command saves the current setup to non-volatile memory. There are 5 re-writeable

memory locations, specified by choosing an index between 1 and 5. Any of the 5 states can be restored
on startup when specified with the SYSTem:BOOTstate command. The parameters saved are the

RF

Power State, Reference Frequency, External LO1 Enabled, External LO1 Switch Override, External LO2
Enabled, External LO2 Switch Override, External Reference Enabled, External Referece Switch Override,
Tune Frequency, Upconverter Bypass Enabled, Upconverter LNA Power State, Upconverter Attenuation
1, Upconverter Attenuation 2, Upconverter ASR State, Downconverter Bypass Enabled, Downconverter
LNA Power State, and Downconverter Attenuation

. For a detailed description of the parameters saved,

see the relevent command descriptions in this manual. NOTE: The MEM_CLR button on the back panel
will rewrite the contents of states 1-5 with the contents of state 0 when depressed, serving as a reset to
factory defaults.

Syntax

*

SAV

Space

NRf

Allowed Values

The

NRf

parameter can be any integer in the range of 1 to 5.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 1 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.2.1

84

«
...
93
94
95
96
97
...
»

Содержание QM1004-0.5-18










































































































Отзывы:

Нет отзывов