Quonset Microwave QM1004-0.5-18 Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 105

Quonset Microwave QM1004-0.5-18 Скачать руководство пользователя страница 93

Combined RF Upconverter/Downconverter

IEEE 488.2 Command Reference

6.7 *RCL

<

NRf

>

The

*RCL

(ReCaLl) command restores a previously saved state from non-volatile memory. In addition

to factory default state 0, there are 5 re-writeable memory locations, specified by choosing an index be-
tween 1 and 5. The restored parameters are the

RF Power State, Reference Frequency, External LO1

Enabled, External LO1 Switch Override, External LO2 Enabled, External LO2 Switch Override, External
Reference Enabled, External Referece Switch Override, Tune Frequency, Upconverter Bypass Enabled,
Upconverter LNA Power State, Upconverter Attenuation 1, Upconverter Attenuation 2, Upconverter ASR
State, Downconverter Bypass Enabled, Downconverter LNA Power State, and Downconverter Attenua-
tion

. For a detailed description of the parameters saved, see the relevent command descriptions in this

manual. When the *RCL command is called, these parameters will be applied to the device.

Syntax

*

RCL

Space

NRf

Allowed Values

The

NRf

parameter can be any integer in the range of 0 to 5.

Error Message

If the parameter is not in the recognized format, error

-102, "Syntax error"

occurs.

If the parameter is less than 0 or greater than 5, error

-222, "Data out of range"

occurs.

Quonset Microwave

Revision 1.2.1

82

«
...
91
92
93
94
95
...
»

Содержание QM1004-0.5-18










































































































Отзывы:

Нет отзывов