Quonset Microwave QM1004-0.5-18 Скачать руководство пользователя страница 43

Страница: 43 / 105

QM1004-0.5-18 Combined RF Upconverter/Downconverter

User Manual

1.3 POWEr Subsystem

Table 4.3:

POWEr Subsystem Commands Summary

Command

Page

Description

POWEr:LNA

Sets or Returns the on/off status of both channels’
LNAs.

POWEr:RF

Turns on or off the RF output of the device.

POWEr:CH1:AT1

Sets or Returns the value of the first upconverter at-
tenuator.

POWEr:CH1:AT2

Sets or Returns the value of the second upconverter
attenuator.

POWEr:CH1:LNA

Sets or Returns the on/off status of the upconverter’s
LNA.

POWEr:CH2:AT1

Sets or Returns the value of downconverter attenua-
tion.

POWEr:CH2:LNA

Sets or Returns the on/off status of the downcon-
verter’s LNA.

1.4 STATus Subsystem

Table 4.4:

STATus Subsystem Commands Summary

Command

Page

Description

STATus:OPERation

Returns the contents of the status event register.

STATus:OPERation:CONDition

Returns the contents of the condition register.

STATus:OPERation:ENABle

Sets the enable bit mask for the status event register.

STATus:PRESet

Presets the STATus:QUEStionable:ENABle register.

STATus:QUEStionable

Returns the contents of the questionable register.

STATus:QUEStionable:CONDition

Returns the contents of the questionable condition reg-
ister.

STATus:QUEStionable:ENABle

Sets the enable bit mask for the questionable register.

Quonset Microwave

Revision 1.2.1

Содержание QM1004-0.5-18










































































































Результаты поиска

Содержание QM1004-0.5-18

Отзывы:

Quonset Microwave QM1004-0.5-18, Руководство пользователя, Страница: 43 / 105

Результаты поиска

Содержание QM1004-0.5-18

Отзывы: