1of2
Assembly Instruction Sheet #IS-RAV8410WT
For Style RAV8410WT
2016 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Package Contents
D
Fixture Body
x 1
A
Crossbar
Assembly
x 1
B
Alternate
Mounting screw
x 2
Please go to
for product cleaning tips. Go to the
selection.
(1) A21 Medium Base Bulb 150W Maximum or
(1) S21 Vintage Medium Base 60W Bulb is recommended but not supplied.
30-45 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
STEP 3
-
Test Fit the Backplate to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (D) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (D) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw
or alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
the backplate and Fixture Body (D) is secure, remove the mounting
ball and Fixture Body (D) and proceed to Step 4.
ReleasedDate:2016-09-26
C
Fixture Loop
x 1
STEP 1
Thread Fixture Loop to
Fixture Body
-
A. Thread the Fixture Loop (C) onto the
Fixture Body (D) and hand tighten
until snug.
C
D
STEP 2
-
Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Figure 2
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
D
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
Mounting Screw
or Alternate Short
Mounting Screw
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all the wire
connections. Twist the connectors until the wires are tightly joined
together. Wrap each connection with approved electrical tape and
carefully stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
