Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-TFIK8407VA
For Style TFIK8407VA
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
A
Crossbar Assembly
x 1
Please go to
for product cleaning tips. Go to the
selection.
(1) A19 Medium Base bulb 100W Maximum, Alternate bulb (1) 23W CFL.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
C
Fixture Body
x 1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
B
Alternate
Mounting
screw
x 2
STEP 1
Install Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Figure 1
Mounting Screw
or Alternate Short
Mounting Screw
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
STEP 2
Test Fitting Backplate to Crossbar Assembly
-
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
backplate on Fixture Body (C) to the Crossbar Assembly (A) and
secure with mounting balls. Note: The backplate on Fixture Body (C)
(Step 2 Continued)
should be snug against the wall and the mounting balls. If not, adjust
the length of the mounting screw or alternate short mounting screw
C
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
on the Crossbar Assembly
(A) by unscrewing the
preassembled hex nut and
lock washer and then
screwing the mounting
screws or alternate short
mounting screws in or out
of the crossbar until the
correct length is achieved.
Once the backplate on
Fixture Body (C) is secure,
remove the mounting ball
and Fixture Body (C) and
proceed to Step 3.
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
ReleasedDate:2016-07-29
