Package Contents
Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone 631.273.2700
Fax
631.231.7102
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape,
safety glasses.
Bulb Recommended:
Estimated Assembly Time:
Preparation:
(2) Medium Base 60W bulbs Maximum, Alternate bulb (2) 13W CFL Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams
below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or
operate the fixture. Contact customer service for replacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-HC1612IB
For Style HC1612IB
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
March2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
B
Cage
x 1
Flat Washer
x 1
C
Glass
Panel
x 4
F
Hex Coupling
x 1
Stem with
Hex Nut
x 1
G
Hardware Contents
AA
Crossbar
x 1
A
Ceiling
Canopy
x 1
H
Knurled
Nut
x 1
BB
CC
DD
Lock Washer
x 1
Hex Nut
x 2
Nipple
x 1
AA
BB
CC
DD
CC
A
Step A
Step D
STEP 1
Install Crossbar
-
A.
AA)
Attach the Crossbar (
to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included) Tighten until snug
.
.
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
AA
Figure 2
Lock Washer
x 1
I
Finial
x 1
STEP 2
Install Nipple to Crossbar
-
*
Pliers is required for this step.
A. Thread one Hex Nut (CC) to the middle of the Nipple (DD). Place the
Lock Washer (BB) over the Nipple (DD) and then thread the Nipple
(DD) into the Crossbar (AA) until the Nipple (DD) is about 0.375
”
above the Crossbar (AA).
B. Position the center hole of the Ceiling Canopy (A) over the end of the
Nipple (DD). Adjust the Nipple (DD) so approx 0.375
”
of the Nipple
(DD) is protruding from the mounting hole on the Ceiling Canopy (A).
This adjustment may take a few tries.
C. Remove the Ceiling Canopy (A) and then tighten the Hex Nut (CC)
against the Crossbar (AA) to secure in place.
D. Thread another Hex Nut (CC) onto the end of the Nipple (DD).
Thread this Hex Nut (CC) on just enough so the inside surface of the
Ceiling Canopy (A) rests against it. * You may have to trial fit the
Ceiling Canopy (A) one more times to insure this distance also. This
Hex Nut (CC) is needed here to prevent you from crushing down the
center of the Ceiling Canopy (A).
E. Refer to Step 3 for wire connections.
F. Attach the Ceiling Canopy (A), the Flat Washer (F) and one Lock
Washer (BB) over the end of the Nipple (DD) as shown. Secure by
threading the Hex Coupling (H) onto the Nipple (DD) and tighten until
snug.
BB
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side Wire
from fixture.
D
Lock Screw
x 8
E
Tab
x 8
J
K
F
H
