Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-EVG8407EK
For Style EVG8407EK
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Crossbar Assembly
x 1
C
Fixture
Body
x 1
STEP 1
Install Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
.
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
Figure 1
STEP 2
Attach Cage to Fixture Body
-
A. Place the top edge of the Cage (D)
over bolts on the bottom edge of the
fixture hood on the Fixture Body (C).
Secure by threading Lock Balls (E)
onto bolts. Hand tighten until snug.
Figure 2
A
Please go to
for product cleaning tips. Go to the
selection.
(1) A19 Medium Base Bulb 100W Maximum.
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
www.quoizel.com
Care + Maintenance
Light Source:
Estimated Assembly Time:
Preparation:
Fixture can only be mounted in the direction indicated on page 2.
Tools Required:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
D
Cage
x 1
E
Lock Ball
x 2
C
E
STEP 3
Test Fitting Backplate
to Crossbar Assembly
-
A.
on Fixture Body
(C) to the
Remove mounting balls from
the Crossbar Assembly (A). Fit
the backplate
Crossbar Assembly
(A) and secure with mounting
balls. Note: The backplate
should be snug
against the wall and the
mounting balls. If
on
Fixture Body (C)
not, adjust the
length of the mounting screws
or alternate short mounting
screws on the Crossbar
Figure 3
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2016-08-15
B
Alternate
Mounting screw
x 2
D
C
Assembly (A) by unscrewing the preassembled hex nut and lock
washer and then screwing the mounting screws or alternate short
mounting screws in or out of the crossbar until the correct length is
achieved. Once the backplate on Fixture Body (C) is secure, remove
the mounting ball and Fixture Body (C) and proceed to Step 4.
Mounting Screw
or Alternate Short
Mounting Screw
Mounting Screw
or Alternate Short
Mounting Screw
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
Figure 5
STEP 5
Install Fixture Body
-
A. Carefully tuck all wires into the
outlet box and position the
backplate of Fixture Body (C)
over the outlet box. Align the
holes in the backplate with the
mounting screws or alternate
short mounting screws. Place
Mounting Ball
A
Backplate
C
Mounting Screw
or Alternate Short
Mounting Screw
caulk (not supplied) into the previously
removed mounting balls and then
attach Fixture using the mounting
balls. Hand tighten until snug.
