2of3
2019 QuoizelInc.
ReleasedDate:2019-03-15
visit us on-line at www.quoizel.com
Figure 7
STEP 5
Installing the Crossbar Assembly
-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the outlet box with the head of the
green ground screw facing you. Secure the Crossbar Assembly (A)
with outlet box screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Mounting Screw
or Alternate Short
Mounting Screw
Figure 5
STEP 6
Test Fit the Backplate to the Crossbar Assembly
-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (E) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (E) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screws
or alternate short mounting screws on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (E) is secure, remove the mounting ball
and Fixture Body (E).
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
E
Mounting Screw
or Alternate Short
Mounting Screw
STEP 7 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 6
STEP 8
-
Install the Fixture Body
A. Position the backplate and Fixture Body (E) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
screws or alternate short mounting screws. Secure the Fixture Body
by using the mounting balls and hand tighten the mounting balls
until snug.
Mounting Ball
A
Backplate
E
Mounting Screw
or Alternate Short
Mounting Screw
Figure 8
STEP 9
-
Apply Silicone Sealer
A. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over top
of backplate and down both sides. Do not caulk the bottom of the
fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade Caulk
Exterior
Grade Caulk
Backplate
Figure 9
HOW TO REPLACE BULB
A. Refer to Step 1 to remove the arm and the cage from the fixture body.
B. Refer to Step 2 to replace the bulb.
C. Refer to Step 4 to reinstall the cage and the arm to the fixture body.
HOW TO REPLACE GLASS PANEL
A. Refer to Step 1 to remove the arm and the cage from the fixture body.
B. Refer to Step 3 to replace the glass panel.
C. Refer to Step 4 to reinstall the cage and the arm to the fixture body.
