1of2
Assembly Instruction Sheet #IS-BEC8406SBK
For Styles BEC8406SBK
2016 QuoizelInc.
ReleasedDate:2016-04-20
Please go to
for product cleaning tips. Go to the
selection.
www.quoizel.com
Care + Maintenance
Tools Required:
Light Source:
Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Integrated 14W LED
20-30 minutes
Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are
present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture. Contact customer service for replacement
parts.
Estimated Assembly Time:
Preparation:
Package Contents
B
Lock Screw
x 4
Inner Backplate
x 1
A
C
Fixture Body
x 1
Front/Back
Glass Panel
x 2
Side Glass
Panel
x 2
D
E
STEP 1
Install Glass
-
A. Unlock the Mounting Ball, remove the
Cage from the Fixture Body (C).
B. Insert Glass Panels (D/E) into slots in the
bottom edge of the Cage. Fold Tabs on the
top edge of the Cage to secure Glass
Panels.
C. Attach the Cage with Glass Panels back
onto fixture hood and secure by threading
the Mounting Ball onto the Bolts. Hand
tighten until snug.
C
D
Cage
Mounting
Ball
Figure 1
E
Tab
Slot
Bolt
B
STEP 2
Install Inner Backplate and
Fixture Body
-
A. Pass the supply wires with Ground
Wire through Inner Backplate (A).
Attach Inner Backplate (A) to Outlet
Box with the head of Green Ground
Screw facing you. Secure it with
Figure 2
A
Outlet
Box
Outlet Box
Screw
Supply Wires
with Ground Wire
Outlet Box Screws (Not
included). Tighten until
snug with screwdrivers
B. Refer to Step 3 for wiring
.
connections.
C. Attach the Fixture Body (C) over the
Inner Backplate (A) and secure with
Lock Screws (B). Tighten until snug
with screwdrivers.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Inner Backplate (A) and Fixture Body (C).
Figure 4
STEP 4
-
Apply Silicone Sealer
A. Make sure exterior wall surface
and fixture backplate are free of
dirt before applying caulk. Using
exterior grade caulk, caulk over
top of backplate and down other
side. Do not caulk bottom of fixture
backplate to ensure proper
moisture drainage.
Your fixture is now assembled and
ready to use. Enjoy!
Backplate
Exterior
Grade
Caulk
HOW TO REPLACE LED MODULE
A. Unlock the Mounting Ball, remove
the Cage from the Fixture Hood.
B. Remove the Glare Guard inside of
the Fixture Hood by unscrewing
Allen Screws. Unscrew Lock
Screws on the LED Module,
remove the LED Module from the
fixture and pull Quick Connectors
out of the Fixture Hood. Separate
the Quick Connector.
C. Replace the LED Module with the
replacement. Connect the new
LED Module to the Quick
Connector and then insert the
Quick Connector inside of the
Fixture Hood. Secure the new
LED Module onto the Fixture
Cage
Mounting
Ball
Allen Screw
Glare Guard
Lock
Screw
LED Module
Quick
Connector
Fixture
Hood
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
