background image

                                                                                                                   

GSM/GPRS/GNSS  Module  Series 

                                                                                                                            MC90-TE-A  User  Guide

 

 

MC90-TE-A_User_Guide                                                                                                                              18 / 21 

(2)  Start the firmware upgrade tool on PC.   

(3)  Press the 

START

 button in the firmware upgrade tool.   

(4)  Switch the S201 and S202 on the EVB to 

ON

 state. For details, please refer to 

document [4]

 

5.5. Compatible Design and Applications 

 

When testing the Wi-Fi function, a built-in Wi-Fi antenna of MC90-TE-A is recommended to be used. In this 

case,  resistor  R213  (0

Ω,  0402  package)  needs  to be  mounted,  while  resistor  R211  (0Ω,  0402  package) 

does not need to be mounted. If an external Wi-Fi antenna is used, then R213 needs to be mounted and 

R211 does not need to be mounted. 

 

Table 2: Resistor to be Mounted when Using Different Wi-Fi Antennas 

 

 

Figure 13: R211 or R213 to be Mounted when Using Different Wi-Fi Antennas   

Resistor 

Use Built-in Wi-Fi Antenna 

Use External Wi-Fi Antenna 

R211 

NM 

0R 

R213 

0R 

NM 

Содержание MC90-TE-A























Отзывы: