Quectel M50 Скачать руководство пользователя

Страница: 69 / 89

M50 Hardware Design

M50_HD_V2.0

- 69 -

3.16. Network status indication

The NETLIGHT signal can be used to drive a network status indicator LED. The working state of

this pin is listed in the following table.

Table 28: Working state of the NETLIGHT

State

Module function

Off

The module is not running.

64ms On/ 800ms Off

The module is not synchronized with network.

64ms On/ 2000ms Off

The module is synchronized with network.

64ms On/ 600ms Off

GPRS data transfer is ongoing.

A reference circuit is shown as below.

Module

300R

4.7K

47K

VBAT

NETLIGHT

Figure 47

: Reference design for NETLIGHT

3.17. Operating status indication

The STATUS pin is set as an output pin and can be used to judge whether module is power-on. In

customer’s design, this pin can be connected to a GPIO of DTE or be used to drive an LED in

order to judge the module’s operation status. A reference circuit is shown in Figure 48.

Table 29: Pin definition of the STATUS

Name

Pin

Description

STATUS

Indicate module operating status

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды