Quectel M50 Скачать руководство пользователя

Страница: 38 / 89

M50 Hardware Design

M50_HD_V2.0

- 38 -

3.5. Charge interface

M50 provides charging function for rechargeable Li-Ion or Lithium Polymer battery. It is

introduced simply in this document. If customer wants to get more information about charging,

please refer to the

document [13].

Table 8: Pin definition of the charging

Name

Pin

I/O

Description.

GATDRV

Charge driving

CHGLDO

Charger power supply source

CHGDET

Charger detection

ISENSE

Current sense

BATSNS

VBAT voltage sense

3.6. Power saving

Upon system requirement, there are several actions to drive the module to enter low current

consumption status. For example, “AT+CFUN” can be used to set module into minimum

functionality mode and DTR hardware interface signal can be used to lead system to SLEEP

mode.

3.6.1. Minimum functionality mode

Minimum functionality mode reduces the functionality of the module to a minimum level, thus

minimize the current consumption when the slow clocking mode is activated at the same time.

This mode is set with the “AT+CFUN” command which provides the choice of the functionality

levels <fun>=0, 1, 4.



0: minimum functionality



1: full functionality (default)



4: disable both transmitting and receiving of RF part

If the module is set to minimum functionality by “AT+CFUN=0”, the RF function and SIM card

function would be disabled. In this case, the UART port is still accessible, but all AT commands

correlative with RF function or SIM card function will be not accessible.

If the module has been set by “AT+CFUN=4”, the RF function will be disabled, the UART port is

still active. In this case, all AT commands correlative with RF function will be not accessible.

After the module is set by “AT+CFUN=0” or “AT+CFUN=4”, it can return to full functionality by

Quecctel

Confidential

Содержание M50


























































































Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды

Quectel M50, Проектирование аппаратного обеспечения

Результаты поиска

Содержание M50

Отзывы:

Похожие инструкции для M50

Бренды по названию

Популярные бренды