Quectel EG21-G Скачать руководство пользователя

Страница: 47 / 96

LTE Module Series

EG21-G Hardware Design

EG21-G_Hardware_Design 46 / 100

PCM_SYNC

PCM data frame
synchronization signal

1.8V power domain

PCM_CLK

PCM data bit clock

1.8V power domain

I2C_SCL

I2C serial clock

Require external pull-up to 1.8V

I2C_SDA

I2C serial data

Require external pull-up to 1.8V

Clock and mode can be configured by AT command, and the default configuration is master mode using
short frame synchronization format with 2048KHz PCM_CLK and 8KHz PCM_SYNC. Please refer to

document [2]

for more details about

AT+QDAI

command.

The following figure shows a reference design of PCM interface with external codec IC.

PCM_IN

PCM_OUT

PCM_SYNC

PCM_CLK

I2C_SCL

I2C_SDA

Module

1.8V

BCLK

LRCK

DAC

ADC

SCL

SDA

MICBIAS

INP

INN

LOUTP

LOUTN

Codec

Figure 24: Reference Circuit of PCM Application with Audio Codec

1. It is recommended to reserve an RC (R=22

, C=22pF) circuits on the PCM lines, especially for

PCM_CLK.

2. EG21-G works as a master device pertaining to I2C interface.

3.13.

SD Card Interface

EG21-G supports SDIO 3.0 interface for SD card.

The following table shows the pin definition of SD card interface.

NOTES

Содержание EG21-G

































































































Результаты поиска

Содержание EG21-G

Отзывы:

Похожие инструкции для EG21-G

Бренды по названию

Популярные бренды

Quectel EG21-G, Проектирование аппаратного обеспечения

Результаты поиска

Содержание EG21-G

Отзывы:

Похожие инструкции для EG21-G

Бренды по названию

Популярные бренды