Quectel EG060V-EA Скачать руководство пользователя

Страница: 43 / 83

LTE-A Module Series

EG060V-EA Hardware Design

EG060V-EA_Hardware_Design 42 / 82

“*” means under development.

3.11. UART Interfaces

The module provides two UART interfaces: the main UART interface and the debug UART interface.

Their features are shown below:

⚫

The main UART interface supports 4800 bps, 9600 bps, 19200 bps, 38400 bps, 57600 bps, 115200

bps, 230400 bps, 460800 bps and 921600 bps baud rates, and the default baud rate is 115200 bps.

This interface is used for data transmission and AT command communication.

⚫

The debug UART interface supports 115200 bps baud rate. It is used for Linux console and log

output.

The following tables show the pin definition.

Table 11: Pin Definition of the Main UART Interface

Table 12: Pin Definition of the Debug UART Interface

Pin Name

Pin No.

I/O

Description

Comment

MAIN_RI

Main UART ring indication

1.8 V power domain

MAIN_DCD

Main UART data carrier detect

1.8 V power domain

MAIN_CTS

Main UART clear to send

1.8 V power domain

MAIN_RTS

Main UART request to send

1.8 V power domain

MAIN_DTR

Main UART data terminal ready

1.8 V power domain

MAIN_TXD

Main UART transmit

1.8 V power domain

MAIN_RXD

Main UART receive

1.8 V power domain

Pin Name

Pin No.

I/O

Description

Comment

DBG_TXD

137

Debug UART transmit

1.8 V power domain

NOTE

Содержание EG060V-EA




















































































Результаты поиска

Содержание EG060V-EA

Отзывы:

Похожие инструкции для EG060V-EA

Бренды по названию

Популярные бренды

Quectel EG060V-EA, Проектирование аппаратного обеспечения

Результаты поиска

Содержание EG060V-EA

Отзывы:

Похожие инструкции для EG060V-EA

Бренды по названию

Популярные бренды