Quectel BG96 Скачать руководство пользователя страница 35

Страница: 35 / 80

LPWA Module Series

BG96 Hardware Design

BG96_Hardware_Design 34 / 79

The reset scenario is illustrated in the following figure.

VBA T

≥150ms

Resetting

Module
Status

Running

RESET_N

Restart

≤460ms

≤0.5V

Figure 12: Timing of Resetting Module

1. Use RESET_N only when turning off the module by

AT+QPOWD

command and PWRKEY pin both

failed.

2. Ensure that there is no large capacitance on PWRKEY and RESET_N pins.

3.8. (U)SIM Interface

The (U)SIM interface circuitry meets ETSI and IMT-2000 requirements. Both 1.8V and 3.0V (U)SIM cards

are supported.

Table 9: Pin Definition of (U)SIM Interface

Pin Name

Pin No.

I/O

Description

Comment

USIM_

PRESENCE

(U)SIM card insertion detection

USIM_VDD

Power supply for (U)SIM card

Either 1.8V or 3.0V is supported

by the module automatically.

USIM_RST

Reset signal of (U)SIM card

USIM_DATA

Data signal of (U)SIM card

USIM_CLK

Clock signal of (U)SIM card

USIM_GND

Specified ground for (U)SIM card

NOTES

Содержание BG96

















































































Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды

Quectel BG96, Руководство пользователя

Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды