Quectel BG96 Скачать руководство пользователя страница 13

Страница: 13 / 80

LPWA Module Series

BG96 Hardware Design

BG96_Hardware_Design 12 / 79

2.2. Key Features

The following table describes the detailed features of BG96 module.

Table 2: Key Features of BG96 Module

Features

Details

Power Supply

Supply voltage: 3.3V~4.3V

Typical supply voltage: 3.8V

Transmitting Power

Class 3 (23dBm±2dB) for LTE-FDD bands

Class 3 (23dBm±2dB) for LTE-TDD bands

Class 4 (33dBm±2dB) for GSM850

Class 4 (33dBm±2dB) for EGSM900

Class 1 (30dBm±2dB) for DCS1800

Class 1 (30dBm±2dB) for PCS1900

Class E2 (27dBm±3dB) for GSM850 8-PSK

Class E2 (27dBm±3dB) for EGSM900 8-PSK

Class E2 (26dBm±3dB) for DCS1800 8-PSK

Class E2 (26dBm±3dB) for PCS1900 8-PSK

LTE Features

Support LTE Cat M1 and LTE Cat NB1

Support 1.4MHz RF bandwidth for LTE Cat M1

Support 200KHz RF bandwidth for LTE Cat NB1

Support SISO in DL direction

Cat M1: Max. 375Kbps (DL)/375Kbps (UL)

Cat NB1: Max. 32Kbps (DL)/70Kbps (UL)

GSM Features

GPRS:

Support GPRS multi-slot class 33 (33 by default)

Coding scheme: CS-1, CS-2, CS-3 and CS-4

Max. 107Kbps (DL)/85.6Kbps (UL)

EDGE:

Support EDGE multi-slot class 33 (33 by default)

Support GMSK and 8-PSK for different MCS (Modulation and Coding

Scheme)

Downlink coding schemes: CS 1-4 and MCS 1-9

Uplink coding schemes: CS 1-4 and MCS 1-9

Max. 296Kbps (DL)/236.8Kbps (UL)

Internet Protocol

Features

Support PPP/TCP/UDP/SSL/TLS/FTP(S)/HTTP(S)/NITZ/PING/MQTT

protocols

Support PAP (Password Authentication Protocol) and CHAP (Challenge

Handshake Authentication Protocol) protocols which are usually used for

PPP connections

Содержание BG96

















































































Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды

Quectel BG96, Руководство пользователя

Результаты поиска

Содержание BG96

Отзывы:

Похожие инструкции для BG96

Бренды по названию

Популярные бренды