Quectel 5G Module Series Скачать руководство пользователя

Страница: 39 / 86

5G Module Series

RM500Q-GL Hardware Design

RM500Q-GL_Hardware_Design 38 / 85

The following figure shows a reference design for (U)SIM interface with a normally closed (U)SIM card

connector.

Module

(U)SIM Card

Connector

USIM_DET

USIM_DATA

USIM_CLK

RST

CLK

USIM_VDD

USIM_RST

VCC

GND

VPP

GND

TVS

10-20k

22R

100 nF

NOTE:

All these resistors, capacitors and TVS should be close to (U)SIM card connector in PCB layout.

Figure 15: Reference Circuit for Normally Closed (U)SIM Card Connector

4.1.4. Normally Open (U)SIM Card Connector

With a normally open (U)SIM card connector, CD1 and CD2 of the connector are disconnected when

there is no (U)SIM card inserted. (U)SIM card detection by low level is applicable to this type of connector.

After executing

AT+QSIMDET=1,0

to enable the (U)SIM hot-plug: when a (U)SIM card is inserted,

USIM_DET will change from high to low level; when the (U)SIM card is removed, USIM_DET will change

from low to high level.

⚫

When the (U)SIM is absent, CD1 is open from CD2 and USIM_DET is at high level.

⚫

When the (U)SIM is present, CD1 is pull down to ground and USIM_DET is at low level.

Содержание 5G Module Series























































































Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды

Quectel 5G Module Series, Проектирование аппаратного обеспечения

Результаты поиска

Содержание 5G Module Series

Отзывы:

Похожие инструкции для 5G Module Series

Бренды по названию

Популярные бренды