background image

Figure 1:

 Back of Tape Drive

 

Figure 2: 

Install in Drive Bay 

Figure 3: 

Terminate SCSI Cable

 

Figure 4:

 Connect the Cables

 

Figure 5:

 Secure the Tape Drive

 

Factory default SCSI ID

SCSI ID jumpers

Power
cable

SCSI cable
(with terminator)

DLT VS160 Tape Drive

Quick Install Guide

Internal Tape Drive (en)

Step 1: Inspect and Prepare the Tape Drive

a. Inspect the shipping box for damage. If you find any damage, report it to the shipping 
company immediately.

Note:

 Save the packing materials in case you need to move or ship the tape drive. You must ship 

the tape drive in the original or equivalent packing materials to preserve your warranty.

b. Select a server or workstation to host your tape drive. Shut down and power off the host and 
all peripheral devices attached to the selected host. 

c. Change the SCSI ID for your tape drive, if necessary. See Figure 1. Use the SCSI jumpers to 
set the SCSI ID. For complete instructions, see the Installation and Operations Guide.

d. Remove the cover from the server or workstation as described in the server or workstation’s 
manual. If necessary, install an LVD/SE host bus adapter in the server or workstation. 

Step 2: Install the Tape Drive

a. Install your tape drive in a half-height drive bay. See Figure 2.

b. Connect an active LVD/SE terminator onto one end of your SCSI cable, if your tape drive is 
the last or only device on the SCSI bus. See Figure 3. If the SCSI cable that came with your SCSI 
host bus adapter already has a terminator built into it, do not use an additional terminator.

Note:

 If the tape drive is not the last or only device on the SCSI bus, make sure the last device on 

the SCSI bus is properly terminated 

and

 is powered on whenever you use your tape drive.

c. Connect the SCSI cable to the tape drive and to the SCSI host bus adapter. Connect the power 
cable to your tape drive. See Figure 4.

d. Secure the tape drive in the selected server or workstation with the appropriate mounting 
screws. See Figure 5. Contact your computer manufacturer if the server or workstation uses 
mounting rails for internal tape drives. 

e. Re-install the cover on the server or workstation. Re-connect the power cables to any attached 
peripheral devices.

f. Power on any attached peripheral devices.

g. Power on the server or workstation and allow its operating system to start. 

Note:

 Turn to the last page for information on additional resources.

Содержание ValueLoader DLT VS160















Отзывы: