background image

WARNING:

 

Risk of electrical shock

 — Before connecting the power 

cords, make sure that both power switches on each tray are off.

Confirm that the two power switches on each tray are off.

Turn on the two power switches on the controller-drive tray. 

Do not turn off the power switches during the power-on process. 

Connect the two power supplies in each tray to separate power 
distribution units (PDUs) in the cabinet. 

If you have expansion drive trays, turn on their two power switches first. 
Then, wait 2 minutes before applying power to the controller-drive tray.

The fans in each tray are very loud when they first start up. The loud 
noise during start-up is normal. 

Check the LEDs and the seven-segment display on the back of each 
controller.

4

5

2

If any of the amber LEDs are on, confirm you completed the installation 
steps correctly. If you are unable to resolve the problem, contact 
technical support. 

Power Switches

Connect power cords 

and apply power

Refer to the 

Hardware Cabling Guide

 for lists of supported cables and 

transceivers, the best practices for cabling, and detailed views of the host 
ports for your controller. Refer to the NetApp Interoperability Matrix 
(

http://mysupport.netapp.com/matrix

) for the supported host topologies.

Before connecting the host cables, confirm that host bus adapters (HBAs) are 
installed in the data hosts. If you are using AIX, wait to connect the data hosts 
until after you have installed and configured the NetApp multipath driver. 
Refer to the 

SANtricity Storage Manager Express Guide

.

Insert the appropriate transceiver into each controller port that you plan to 
use, based on the host protocol and the host topology. Start with the lowest 
numbered controller port.
You do not need transceivers for copper iSCSI. 

Connect to the data hosts as follows:

2

To use direct attach topology,

 connect each HBA directly to the 

host ports on controllers A and B, as in this example: 

To use fabric topology,

 connect each HBA to a switch that is 

connected to the host ports on controllers A and B, as in this example. 
To zone a switch, follow the instructions in the appropriate 

SANtricity 

Express Guide.

Data hosts with 

redundant 

HBA ports

HBA 2

HBA 1 HBA 2

HBA 1

HBA 2

HBA 1

Storage array 

with two host 

ports/controller

Data hosts with 

redundant 

HBA ports

Redundant zoned 

switches

Storage array 

with four host 

ports/controller

HBA 2

HBA 1 HBA 2

HBA 1

HBA 2

HBA 1

A

B

A

B

Connect to the data hosts

The seven-segment display shows the repeating sequence 

OS, Sd, 

blank

 to 

indicate that the controller is performing start-of-day processing. After the 
controller has booted up, the display shows the tray ID. 

6

Содержание StorNext QD7000


















Отзывы: