Quantum ODYSSEY HF Series Скачать руководство пользователя страница 82

Страница: 82 / 493

Chapter 2 Assembly & Installation

Revision W

HF Series X-ray Generators - Service Manual

2-46

Quantum Medical Imaging

6. The Power/Expose Control Box (AY20-271) must be installed between the

Generator and the "Non-patient Area" in which the Q-VISION OCP and

the Operator will be positioned. The Power/Expose Control Box should

be securely mounted in close proximity to the Operator’s position for easy

access to the ON/ STANDBY Switch, and in clear view of the Q-VISION

OCP. A 30-inch expansion cable for the 2-stage Expose Switch is hard-

wired to the Power/Expose Control Box.

Figure 2-24c. Power/Expose Control Box

7. A prefabricated 50-ft. or 100 ft. cable with 6-pin modular plugs (AY51-

243-XXX), is supplied for connecting the Power/Expose Control Box to the

generator OCP Interface Board (AY40-073S). See Figure 2-24c. DO NOT

route cable through an opening in the generator containing a High Volt-

age Cable (see Figure 2-13).

8. On systems provided with a Wall Mount Kit (option QGV-WM), install the

wall mount components (VESA Mount Adapter, VESA Mount Plate, and

Wall Mount Bracket) in accordance with instructions provided with the

Wall Mount Kit.

9. Ensure wall attachment hardware is suitable for wall construction type

(each screw capable of supporting 25 lbs. pull load).

Integrated Workstation Operator Control Panel
If the generator is to be integrated with an external digital imaging worksta-

tion computer for operation as a generator control panel, the "Q-Connect"

option must be installed in the generator. This option provides an Ethernet

adapter to enable connection of the generator to the workstation personal

computer (PC). Typically, this adapter is factory installed, and is ready for use

when the unit is shipped. If the Q-Connect Ethernet adapter is needed,

6-PIN
MODULAR
PLUG

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды