Quantum ODYSSEY HF Series Скачать руководство пользователя страница 410

Страница: 410 / 493

Appendix B Calibration (DiRex System)

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

B-47

Film Screen Selection
Calibration of film/screen combinations should be performed in the following

sequence, assuming a typical radiographic system having one ion chamber in

the wall stand (72" and 40" SID), and a second ion chamber used in the

radiographic table (40" SID).
If the system is using a wall stand and 200 and 400 speed films, calibrate the

Wall 72" film screen combination using 200 speed film first, followed by Wall

72" using 400 speed film.
If the system only has a table receptor, perform all AEC calibrations (i.e., ion

chamber balance, AEC MAS balance, AEC optical density, and AEC KVP proce-

dures).

IMPORTANT NOTE: Typically, the AEC calibration

parameters for each of the various receptors used

with the generator are quite similar. Therefore, the

HF Series generator’s calibration data "Copy Film

Screen" function can be used to copy the calibration

parameters from one receptor (i.e., a calibrated

receptor) to the other receptors. For example, after

completing AEC calibration of 72" Wall film/screen,

the Copy Film Screen function can be used to copy

the 72" film/screen calibration data to 40" Wall

film/screen.

After copying AEC data, the only further AEC cali-

bration usually required for the 40" film/screen is

performing AEC OD Calibration to set the "AEC Ref"

value. Similarly, the 40" Wall film/screen calibra-

tion data can be copied to the 40" Table, however,

the table ion chamber’s MASTER GAIN potentiome-

ter must be adjusted as required. Be sure to verify

the AEC films for each SID/receptor meet applica-

ble regulatory agency requirements. If required,

further optical density accuracy can be attained by

performing the "AEC KV Calibration" procedure.

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды