Quantum ODYSSEY HF Series Скачать руководство пользователя страница 400

Страница: 400 / 493

Appendix B Calibration (DiRex System)

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging, LLC

B-37

MA Calibration

This procedure calibrates the generator to verify accurate system measure-

ment of tube current (mA). Current measurement accuracy is verified using a

pre-calibrated mAs meter (Dynalyzer or equivalent) as a benchmark. Ensure

precision of the measurement instrument is sufficient enough to assure gen-

erator accuracy requirements can be met.
An oscilloscope may be used for mA measurement, however, it likely will not

be precise enough to assure generator mA accuracy. To use an oscilloscope

for mA measurement, connect scope leads between test point TP7 on KVP

Control Board A2 (AY40-003S1) and ground. Set scope for 1.0 volt/division,

and 50 ms/division time base. This will give a 100 mA/volt equivalent for mA

measurement (see Figure B-23a for sample mA measurements using scope).

Figure B-23a. MA Measurement Using an Oscilloscope

Proceed as follows:

WARNING! To avoid injury to personnel, ensure

that system power is removed prior to making

and removing any electrical connections.

1. If not already done so, a kVp bleeder tank should be connected in series

between tube and High-Voltage (H.V.) Transformer A17. If using a mAs

meter, connect the mAs meter between pins A17P1-9 and A17P1-10 on

H.V. Transformer A17. This connection is made by removing the two

green/yellow wires connecting A17P1-9 and A17P1-10 to the ground stud
on top of the H.V. Transformer (see Figure B-22) and connecting the

removed wires to the mAs meter. (Note: The MAS meter should remain

connected throughout calibration.

These wires must be re-connected

when finished calibration

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды