Quantum ODYSSEY HF Series Скачать руководство пользователя страница 39

Страница: 39 / 493

Chapter 2 Assembly & Installation

HF Series X-ray Generators - Service Manual

Revision W

Quantum Medical Imaging

2-3

OVERVIEW

This chapter provides procedures for installing the HF Series x-ray generator, from

pre-installation guidelines to final system inspection prior to operational readiness.

These procedures should be reviewed carefully before beginning the actual installa-

tion. Preparing the X-ray generator for operation requires completion of the following

tasks:

•

Installing the X-ray generator cabinet

•

Installing the Operator Control Panel (OCP)

•

Making the Electrical Cable Connections

•

Power-up

•

Calibrating the generator

•

Inspecting the system

•

Verifying programmed techniques

WARNING! Equipment installation and servicing

procedures should be performed by properly

trained and qualified service personnel only.

PRE-INSTALLATION GUIDELINES

While site planning is the customer's responsibility, the following are recom-

mended guidelines.

Verify Equipment Location
In radiology site preparation, it is essential to verify the location and space

allocated for the equipment is sufficient. See Figures 1-1 through 1-3 for HF

Series x-ray generator dimensions. The room plan should show the following

for the equipment:

•

All working and parked positions

•

Overall dimensions

•

Total equipment weights and power outputs

•

Structural mounting and attachment methods

Ensure sufficient air circulation space is provided between the rear side of

Generator Cabinet and wall (4.0" min.). The floor where the generator is

installed should be flat and approximately level (minor shimming is accept-

able) and capable of supporting a load of 500 lbs. (226.8 kg).
If the generator is equipped with the "Q-Connect option" (ethernet adapter

for connection to Q-VISION or for integration with a Digital Radiographic Sys-

tem), the associated computer monitor functions as the generator operator

control panel (OCP). If the workstation is qualified to standard UL 60950/IEC

Содержание ODYSSEY HF Series














































































































































































































































































































































































































































































































Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды

Quantum ODYSSEY HF Series, Руководство по обслуживанию

Результаты поиска

Содержание ODYSSEY HF Series

Отзывы:

Бренды по названию

Популярные бренды