Quantum LTO-8 HH SAS Скачать руководство пользователя страница 64

Страница: 64 / 126

Chapter 4: Operations
Diagnostic and Maintenance Functions

QuantumLTO-8 HH SAS User’s Guide

release. When the diagnostic ends,

temporarily appears in the

SCD, and the tape drive exits Maintenance Mode.

• If an error is detected, the Fault light flashes and the drive posts

an error code to the SCD. To determine the error, locate the
code in

Appendix A, Error Codes and Messages

. To clear the

error either turn the power off and then on again, or reboot the

drive by pressing and holding the

Unload

button for 10

seconds.

Function Code 8:

Unmake FUP Tape

Function Code 8

erases the firmware update (FUP) data and rewrites

the cartridge memory on the tape. This converts the cartridge into a
valid scratch (blank) data cartridge.

Place the drive in maintenance mode. For instructions, see

Entering

Maintenance Mode

on page 48.

Press the

Unload

button once per second until

appears in the

SCD. (If you cycle past the desired code, press the

Unload

button

once per second until the code reappears.)

Press and hold the

Unload

button for three or more seconds, then

release it to select function

. The SCD changes to a flashing

requesting a cartridge.

Insert the FUP data cartridge (or the tape drive exits maintenance
mode). The SCD changes to a flashing

. The tape drive erases the

firmware on the tape and rewrites the header in the cartridge
memory to change the cartridge to a valid scratch (blank) data
cartridge. The drive then ejects the cartridge and exits Maintenance
Mode.

Note:

If you inserted an invalid tape cartridge, error code

appears in the SCD. If you inserted a write-protected cartridge,
or the media has read-only compatibility, error code

appears

in the SCD. In either case, the tape drive unloads the cartridge

and exits Maintenance Mode after the cartridge is removed.

• If the tape drive creates the scratch tape successfully, it rewinds

and unloads the new tape, exits Maintenance Mode, and the
tape is ready to use.

• If the tape drive fails to create the scratch tape, it displays an

error code. To determine the error, see

Appendix A, Error Codes

Содержание LTO-8 HH SAS































































































































Результаты поиска

Содержание LTO-8 HH SAS

Отзывы:

Бренды по названию

Популярные бренды

Quantum LTO-8 HH SAS, Техническое справочное руководство

Результаты поиска

Содержание LTO-8 HH SAS

Отзывы:

Бренды по названию

Популярные бренды