Quantum LTO-8 HH SAS Скачать руководство пользователя страница 59

Страница: 59 / 126

Chapter 4: Operations

Diagnostic and Maintenance Functions

QuantumLTO-8 HH SAS User’s Guide

• If the update completes successfully, the tape drive rewinds and

unloads the FUP tape, resets itself, and is ready to use the new
firmware. The drive automatically reboots.

• If the update fails, the tape drive posts an error code to the SCD.

To determine the error, locate the code in

Appendix A, Error

Codes and Messages

. Push the

Unload

button to eject the

cartridge. The drive exits Maintenance Mode after the cartridge
is removed. Contact Quantum Technical Support for problem

determination or machine replacement.

Function Code 3: Create

FUP Tape

Function Code 3

copies the drive's firmware update (FUP) data to a

scratch data cartridge. The resulting FUP tape can only be used to
update the firmware on other LTO-8 tape drives with the same host
interface (SAS, or Fibre Channel).

Caution:

For this function, insert only a scratch (blank) data
cartridge or a cartridge that may be overwritten. During

the test, the drive overwrites the data on the cartridge.

Note:

If you inserted an invalid tape cartridge, error code

appears in the SCD. If you inserted a write-protected cartridge,
or the media has read-only compatibility, error code

appears

in the SCD. In either case, the tape drive unloads the cartridge

and exits Maintenance Mode after the cartridge is removed.

Place the drive in Maintenance Mode. For instructions, see

Appendix 4, Entering Maintenance Mode

Press the

Unload

button once per second until

appears in the

SCD. (If you cycle past the desired code, press the Unload button
once per second until the code reappears.)

Press and hold the

Unload

button for three or more seconds, then

release it to select the function. The SCD changes to a flashing

Insert a scratch (blank) data cartridge that is not write protected (or
the tape drive exits maintenance mode). The SCD changes to a
flashing

. The tape drive copies the FUP data to the scratch data

cartridge.

Содержание LTO-8 HH SAS































































































































Результаты поиска

Содержание LTO-8 HH SAS

Отзывы:

Бренды по названию

Популярные бренды

Quantum LTO-8 HH SAS, Техническое справочное руководство

Результаты поиска

Содержание LTO-8 HH SAS

Отзывы:

Бренды по названию

Популярные бренды