Quantech QCC2015CEE Скачать руководство пользователя страница 32

Страница: 32 / 172

QUANTECH

Form QCC2-NM1

Issue Date: 5/20/2021

SECTION 4 – INSTALLATION

Air proving switch/remote start-stop contacts

The Air Flow Switch MUST NOT be used

to start and stop the chiller (i.e. starting

and stopping the blower). It is intended

only as a safety switch.

The air proving switch is field wired to XTBC1 ter-

minals 13 to 14 to prevent operation of the refrigerant

circuit when the supply air blower is not operating.
If separate evaporator blowers are used with respect

to each refrigerant system in the condensing unit, then

two air proving switches (used for each blower) must

be wired in series across XTBC1 terminals 13 - 14. See

Figure 10 on page 37 and the unit wiring diagrams

starting on page 50.

Evaporator blower start contacts

For constant fan operation: Terminal block XTBC2 -

terminals 23 to 24, are normally open contacts that can

be used to switch field supplied power to provide a start

signal to the evaporator blower contactor. Contacts will

close whenever the daily schedule is programmed for

cooling. See

Figure 10 on page 37 and the unit wiring

diagrams starting on page 50.

Relief valves

Relief valves are located on both the high and low

pressure side of the piping. The high side relief valve

pressure setting is 650 psig. The low side relief valve

pressure setting is 450 psig.

High pressure cutout

A high pressure cutout is installed in the discharge pip-

ing of each system. The cutout opens at 585 psig plus

or minus 10 psig and closes at 440 psig plus or minus

25 psig.

Compressor heaters

Compressor heaters are standard on all models. If pow-

er is OFF more than two hours, the crankcase heaters

must be energized for 18 to 24 hours before restarting

a compressor. This will ensure that liquid slugging and

oil dilution does not damage the compressors on start.

Refrigerant piping
General

When the unit has been located in its final position, the

unit piping may be connected. Normal installation pre-

cautions should be observed in order to receive maxi-

mum operating efficiencies. System piping should con-

form to the YORK DX piping guide

Form 050.40-ES2

or ASHRAE refrigeration handbook guidelines. All

piping design and installation is the responsibility of

the user.

QUANTECH ASSUMES NO WARRANTY RE‑

SPONSIBILITY FOR SYSTEM OPERATION

OR FAILURES DUE TO INCORRECT PIPING,

PIPING DESIGN, CONTROL PROBLEMS, OR

LACK OF OIL RETURN.

Filter driers and sight glasses are shipped loose for field

installation on each refrigerant circuit. Field refrigerant

piping can be connected to the condensing unit.
All expansion valves, liquid line solenoid valves, and

refrigerant piping are field supplied and installed. TXV

sizing should be equal in size or slightly smaller than

the capacity of the circuit. If multiple coil sections are

utilized, a TXV for each section (sized accordingly)

must be installed.

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 32 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: