Quantech QCC2015CEE Скачать руководство пользователя страница 153

Страница: 153 / 172

QUANTECH

153

Form QCC2-NM1

Issue Date: 5/20/2021

Section 10 – Maintenance

It is the responsibility of the equipment owner to pro-

vide maintenance on the system.

Important

If system failure occurs due to incorrect maintenance

during the warranty period, Quantech will not be liable

for costs incurred to return the system to satisfactory

operation. The following is intended only as a guide

and covers only the unit components. It does not cover

other related system components which may or may

not be furnished by Quantech. System components

should be maintained according to the individual man-

ufacture’s recommendations as their operation will af-

fect the operation of the unit.

Compressors
Oil level check

The oil level can only be tested when the compressor

is running in stabilized conditions, to ensure that there

is no liquid refrigerant in the lower shell of the com-

pressor. When the compressor is running at stabilized

conditions, the oil level must be between 1/4 and 3/4

in the oil sight glass. Note: at shutdown, the oil level

can fall to the bottom limit of the oil sight glass. Use

YORK “V” oil when adding oil.

Oil analysis

The oil used in these compressors is pale yellow in

color (POE oil). If the oil color darkens or exhibits a

change in color, this may be an indication of contami-

nants in the refrigerant system. If this occurs, an oil

sample should be taken and analyzed. If contaminants

are present, the system must be cleaned to prevent

compressor failure.

Never use the scroll compressor to pump

the refrigerant system down into a vacuum.

Doing so will cause internal arcing of the

compressor motor which will result in fail-

ure of compressor.

Condenser fan motors

Condenser fan motors are permanently lubricated and

require no maintenance.

Condenser coils

Dirt should not be allowed to accumulate on the con-

denser coil surfaces. Cleaning should be as often as

necessary to keep coils clean.

Exercise care when cleaning the coil so

that the coil fins are not damaged.

Operating parameters

Regular checks of the system should be preformed to

ensure that operating temperatures and pressures are

within limitations, and that the operating controls are

set within correct limits.

Refer to the Operation, Start-

Up, and Installation sections of this manual.

Onboard battery backup

U5 is the Real Time Clock chip located on the 031-

02630 IPU II board that maintains the date/time and

stores customer programmed setpoints. The Real Time

Clock is a 128K bram, P/N 031-02565-000. The IPU

II board must have JP1 installed when the 128K bram

is installed.

Do not confuse JP1 on the IPU II (031-

02630) board with JP1 on the I/O (031-

02550) board.

Overall unit inspection

In addition to the checks listed on this page, periodic

overall inspections of the unit should be accomplished

to ensure correct equipment operation. Items such

as loose hardware, component operation, refrigerant

leaks, unusual noises, etc. should be investigated and

corrected immediately.

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 153 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: