Quantech QCC2015CEE Скачать руководство пользователя страница 136

Страница: 136 / 172

QUANTECH

136

Form QCC2-NM1

Issue Date: 5/20/2021

SECTION 8 – UNIT OPERATION

System lead/lag

(Discharge Air Temp Control Only)

Lead/lag between systems may be selected to help

equalize average run hours between systems on con-

densing units with two refrigerant systems. This may

be programmed under the OPTIONS key. Auto lead/

lag allows automatic lead/lag of the two systems based

on average run hours of the compressors in each sys-

tem. Manual lead/lag selects specifically the sequence

in which the microboard starts systems. Systems in

Suction Pressure Control act independently based on

the individual Suction Pressure Control setpoints.

Compressor lead/lag

The compressors within a system rotate starts in se-

quence 1, 2 or 1, 2, 3 with wraparound. The longest

OFF compressor in a system will start first, and the

longest-running compressor in a system will turn OFF

first. When unloading, the system with the most com-

pressors on unloads first. The lag system will shut

down a compressor first when equal numbers of com-

pressors are operating in each system. The microboard

will not attempt to equalize run time of compressors in

a system.
Once the second system has started a compressor, the

microboard will attempt to equally load each system.

Once this occurs, loading will alternate between sys-

tems.
If Soft Start is enabled on European models with this

option, compressor lead/lag will function as outlined in

Option 12 under the OPTIONS key.

Anti-recycle timer

The programmable anti-recycle timer ensures that sys-

tems do not cycle. This timer is programmable under

the PROGRAM key between 300 and 600 seconds.

Whenever possible, to reduce cycling and motor heat-

ing, the anti-recycle timer should be adjusted to 600

seconds. The programmable anti-recycle timer starts

the timer when the first compressor in a system starts.

The timer begins to count down. If all of the compres-

sors in a circuit cycle OFF, a compressor within the cir-

cuit will not be permitted to start until the anti-recycle

timer has timed out. If the lead system has run for less

than five minutes, three times in a row, the anti-recycle

timer will be extended to 10 minutes.

Anti-coincidence timer

This timer is not present on single-system units. Two

timing controls are present in software to ensure com-

pressors within a circuit or between systems, do not start

simultaneously. The anti-coincidence timer ensures

there is at least a one minute delay between system starts

on two circuit systems. This timer is NOT programma-

ble. The load timers further ensure that there is a mini-

mum time between compressor starts within a system.

Evaporator blower control

The evaporator blower start contacts (XTBC2 - terminals

23 - 24) are energized when any of the following condi-

tions are true:

1. Any compressor is running.
2. Daily Schedule is not programmed OFF and

Unit Switch is ON.

The contacts will not close if the micropanel has been

powered up for less than 30 seconds or if the contacts

have been closed in the last 30 seconds to prevent mo-

tor overheating. These contacts can be used to start the

evaporator blower, and for all practical purposes, will

be running in a “constant fan” mode. However, if the

blower is desired to cycle with the compressors, then

cycling of the evaporator blower can be achieved by

using the “Run Contacts” located at or XTBC2 - termi-

nals 27 to 28 for system two (if applicable).

Evaporator heater control

The evaporator heater is controlled by ambient air tem-

perature. When the ambient temperature drops below

40°F (4.4°C) the heater is turned ON. When the tem-

perature rises above 45°F (7.2°C) the heater is turned

OFF. An under voltage condition will keep the heater

off until full voltage is restored to the system.

Pumpdown control

Each system has a pump-down feature upon shut-

off. Manual pumpdown from the keypad is possible

by turning off the respective system’s switch under

the OPTIONS key. On a non-safety, non-unit switch

shutdown, all compressors but one in the system will

be shut OFF. The LLSV will also be turned OFF. The

final compressor will be allowed to run until the suc-

tion pressure falls below the cutout, or for 180 seconds,

whichever comes first

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 136 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: