Quantech QCC2015CEE Скачать руководство пользователя страница 103

Страница: 103 / 172

QUANTECH

103

Form QCC2-NM1

Issue Date: 5/20/2021

Section 7 – Unit controls

LD22346

Introduction

The Quantech Millenium MicroComputer Control

Center is a microprocessor based control system de-

signed to provide the entire control for the liquid con-

densing unit. The control logic embedded in the mi-

croprocessor based control system will provide control

for the suction pressure or discharge air temperature, as

well as sequencing, system safeties, displaying status,

and daily schedules. The MicroComputer Control Cen-

ter consists of four basic components:

1.  Microprocessor Board
2.  Transformer
3.  Display
4.  Keypad.

The keypad allows programming and accessing set-

points, pressures, temperatures, cutouts, daily sched-

ule, options, and fault information.
Remote cycling, demand limiting and chilled liquid

temperature reset can be accomplished by field sup-

plied contacts.
Compressor starting/stopping and loading/unload-

ing decisions are performed by the Microprocessor to

maintain suction pressure or discharge air temperature.

These decisions are a function of temperature devia-

tion from setpoint.
A Master ON/Off switch is available to activate or de-

activate the unit.

Microprocessor board

The Microprocessor Board is the controller and deci-

sion maker in the control panel. System inputs such

as pressure transducers and temperature sensors are

connected directly to the Microprocessor Board. The

Microprocessor Board circuitry multiplexes the ana-

log inputs, digitizes them, and scans them to keep a

constant watch on the unit operating conditions. From

this information, the Microprocessor then issues com-

mands to the Relay Outputs to control contactors, so-

lenoids, etc. for Temperature Control and to react to

safety conditions.
Keypad commands are acted upon by the microboard

to change setpoints, cutouts, scheduling, operating re-

quirements, and to provide displays.
The on-board power supply converts 24 VAC from the

1T transformer to a +12 VDC and +5 VDC regulated

supply located on the Microprocessor Board. This volt-

age is used to operate integrated circuitry on the board.

The 40 character display and unit sensors are supplied

power from the microboard 5VDC supply.
24 VAC is rectified and filtered to provide unregulat-

ed +30 VDC to supply the flow switch, PWM remote

temperature reset, and demand limit circuitry which is

available to be used with field supplied contacts. The

Microprocessor Board energizes on-board relays to

output 120 VAC to motor contactors, solenoid valves,

etc. to control system operation. 120 VAC is supplied

to the optimal T3 Transformer, which supplies 12 VAC

to the bridge diode module. The Bridge Diode Module

rectifies the voltage to -12 V unregulated The +12 V

unregulated voltage supplies power to the Remote

Temperature Reset Circuit Board.

Содержание QCC2015CEE













































































































































































Результаты поиска

Содержание QCC2015CEE

Отзывы:

Quantech QCC2015CEE, Инструкция по установке, эксплуатации и обслуживанию, Страница: 103 / 172

Результаты поиска

Содержание QCC2015CEE

Отзывы: