manualshive.com logo in svg

Quanser 3 DOF, Лабораторное руководство, Страница: 13 / 18

Поделиться
Скачать
Quanser 3 DOF Скачать руководство пользователя страница 13

4

SYSTEM REQUIREMENTS

Required Software

Make sure

LabVIEW™

is installed with the following required add-ons:

1.

LabVIEW™

2. NI-DAQmx

3. NI

LabVIEW™

Control Design and Simulation Module

4. NI

LabVIEW™

MathScript RT Module

5.

Quanser Rapid Control Prototyping Toolkit

r

Note

: Make sure the Quanser Rapid Control Prototyping (RCP) Toolkit is installed after LabVIEW. See the RCP

Toolkit Quick Start Guide for more information.

Required Hardware

• Data acquisition (DAQ) device

with four encoder inputs

and that is compatible with

Quanser Rapid Control

Prototyping Toolkit

r

. This includes Quanser DAQ boards such as Q8-USB, QPID, and QPIDe and some

National Instruments DAQ devices.

• Quanser 3 DOF Gyroscope

• Quanser AMPAQ-L4 power amplifier, or equivalent.

Before Starting Lab

Before you begin this laboratory make sure:

•

LabVIEW™

is installed on your PC.

• DAQ device has been successfully tested (e.g., using the test software in the Quick Start Guide or the

Analog

Loopback Demo

).

• 3 DOF Gyroscope and amplifier are connected to your DAQ board as described its User Manual [2].

3D GYRO Laboratory Guide

v 1.1

Содержание 3 DOF



















Отзывы:

Нет отзывов