Quality Water For Less Fleck 2510 Скачать руководство пользователя страница 13

PAGE 13

Help: 888-426-5001

QualityWaterForLess.com

f I G u r e   13 - a

f I G u r e   13 - e

f I G u r e   13 - f

f I G u r e   13 - d

f I G u r e   13 - b

f I G u r e   13 - c

6   › d r a I n   c o n n ec t I o n

1)  Locate the barbed fitting and use Teflon tape to 

wrap the threading as shown in Figure 13-A. 

Be 

careful to wrap the tape clockwise with the 

threading towards you.

 Attach the barbed fit-

ting to the DLFC fitting and 

i

 Please use cau-

tion not to over tighten the barbed fitting

2)  Move to the rear of the Fleck 2510 SXT control 

valve, find the drain fitting pin and remove it to 
allow you to insert the DLFC/barbed drain fitting 
as seen in Figure 13-B

3)  Insert the DLFC/Barbed fitting as seen in Figure 

13-C. 

Be sure that the fitting is fully inserted 

into the drain port by clicking it into place

4)  Reinsert the drain fitting pin to lock the DLFC/

barbed drain fitting into the Fleck 2510 SXT con-
trol valve as seen in Figure 13-D

5)  Next, assemble your ½” I.D. drain line to the drain 

barb as shown in Figure 13-E. 

Be sure to use rigid 

wall ½” I.d. tubing that will not flatten.

 

Wrap 

electrical tape over the drain tubing to prevent a tube 
split and clamp the tubing securely into place with the 
included blue clamp as shown in Figure 13-F

6)  Connect the other end of this drain line tubing se-

curely to a standpipe or drain in accordance with all 
local plumbing codes. 

Be sure that the drain line 

is securely in place before putting your softener 

in service. during regeneration, there will be 

increased flow via this tubing which may cause 

the tubing to become loose

Содержание Fleck 2510



















Отзывы: