background image

 

 Quadratec

®

 1.75”  

 Coil Suspension Lift Kit  

TO REDUCE RISK OF SERIOUS INJURY OR PROPERTY DAMAGE: 

READ ALL SAFETY MESSAGES AND UNDERSTAND ALL 

INSTRUCTIONS AND PROCEDURE 

NOTICES

 BEFORE ATTEMPTING 

TO INSTALL OR USE THIS PRODUCT. FOLLOW ALL INSTRUCTIONS

AND WARNINGS WITH PRODUCT & VEHICLE OWNERS MANUAL.

THIS KIT INCLUDES A COCKPIT SAFETY WARNING STICKER 

REGARDING INCREASED ROLLOVER RISK. THIS STICKER 

MUST BE AFFIXED IN THE COCKPIT, VISIBLE TO ALL VEHICLE 

OCCUPANTS AT ALL TIMES.

RISK OF EYE INJURY! SAFETY GLASSES MUST BE WORN AT ALL

TIMES WHILE INSTALLING OR MAINTAINING THIS PRODUCT.

TORQUE AND RECHECK FASTENERS AFTER 250 MILES AND

FREQUENTLY THEREAFTER. DO NOT USE IF DAMAGED.

Installation Manual: for 2018 - Current Wrangler (JL) 

#16400.0010 

PARTS LIST:

Front Coil Spacers - QTY 2
Rear Coil Spacers - QTY 2
Front Swaybar Links - QTY 2
Front Bump Stops - QTY 2 
Rear Bump Stops - QTY 2
Front Shock Brackets - QTY 2
Rear Shock Brackets - QTY 2
Full Kit Component & Hardware Listed Inside Booklet
Cockpit Warning Sticker - QTY 1

QJL_1.75_LIFT_16400_0010_LTR.indd   1

QJL_1.75_LIFT_16400_0010_LTR.indd   1

9/11/20   1:27 PM

9/11/20   1:27 PM

Содержание 16400.0010













Отзывы: