Quadra-Fire TOPAZ-MBK-IPI страница 44 Скачать руководство пользователя

Страница: 44 / 62

Quadra-Fire • TOPAZ-MBK-IPI, TOPAZ-D-PMH-IPI, TOPAZ-D-MBK-IPI, TOPAZ-D-CSB-IPI Installation Manual • 2341-980_R10 • 11/15

A. General Information

WARNING! Risk of Shock or Explosion! DO NOT

wire

110-120 VAC to the valve or to the appliance wall switch.

Incorrect wiring will damage controls.

NOTICE:

This appliance must be electrically wired and

grounded in accordance with local codes or, in the absence

of local codes, with

National Electric Code ANSI/NFPA

70-latest edition

or the

Canadian Electric Code CSA C22.1.

• Plug the cord from the appliance junction box to

unswitched 110-120 VAC. This is required for proper

operation of the appliance.

• A 110-120 VAC circuit for this product must be protected

with ground-fault circuit-interrupter protection, in

compliance with the applicable electrical codes, when it is

installed in locations such as in bathrooms or near sinks.

• Low voltage and 110-120 VAC voltage cannot be shared

within the same wall box.

WARNING! Risk of Shock!

Plug 3-pronged (grounding)

plug directly into a properly grounded 3-pronged receptacle.

DO NOT cut or remove grounding prong from plug.

Accessories Requirements

• This appliance may be used with a wall switch, wall

mounted thermostat and/or a remote control.

Wiring for optional Hearth & Home Technologies approved

accessories should be done now to avoid reconstruction.

Follow instructions that come with those accessories.

Electrical Service and Repair

WARNING! Risk of Shock!

Label all wires prior to

disconnection when servicing controls. Wiring errors can

cause improper and dangerous operation. Verify proper

operation after servicing.

WARNING! Risk of Shock!

Replace damaged wire with

type 105º C rated wire. Wire must have high temperature

insulation.

Electrical Information

Содержание TOPAZ-MBK-IPI































































Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды

Quadra-Fire TOPAZ-MBK-IPI, Руководство по установке

Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды