Quadra-Fire TOPAZ-MBK-IPI страница 25 Скачать руководство пользователя

Страница: 25 / 62

Quadra-Fire • TOPAZ-MBK-IPI, TOPAZ-D-PMH-IPI, TOPAZ-D-MBK-IPI, TOPAZ-D-CSB-IPI Installation Manual • 2341-980_R10 • 11/15

Existing Masonry Chimney

Prior to installing the gas stove, ensure that the existing chimney is functionally sound and clean.
• Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home
Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certified

professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

• Replace component parts of the chimney and fireplaceas specified by the professionals.
• See Section 11 for venting components.

Type C - Up & Out Installation

Type D - Hearth Mount

Figure 4.22

Type A & B Co-Axial to Co-Linear

Chimney Liner Termination Cap

(Included in Chimney Liner

Termination Kit)

Co-Axial to

Co-Linear Connector

(Part 46DVA-GCL)

3 in. (76mm) Flex Liner

(Included in Chimney Liner

Termination Kit)

Showing two 30 ft.

(9m) Sections of

Flex Liner

Chimney Liner Termination Cap

(Included in Chimney Liner Termination Kit)

Co-Axial to Co-Linear

Connector

(Part 46DVA-GCL)

30 ft. (9m) of 3 in. (76mm) Flex

Liner Exhaust Section

(Included in Chimney Liner Termination Kit)

4 ft. (1m) of 3 in. (76mm)

Flex Liner Air Intake Section

(Included in Chimney Liner Termination Kit)

The chimney must be sealed from the

4 ft. (1m) section to termination using

a smoke shelf or a flue restrictor. The

seal should be a minimum of 6 in.

(152mm) below the end of the 4 ft.

(1m) Air Intake section.

This section of the chimney

must be sealed

TERMINATION CAP

(Included in Link-Stove kit)

FLASHING

(Included in Masonry
Chimney Conversion Kit)

4 in. (102mm) FLEX LINER

(Included in Link-Stove kit)

TOP ADAPTOR

(Included in Masonry Chimney
Conversion Kit)

RETRO CONNECTOR

(Included in Masonry Chimney
Conversion Kit)

90° ELBOW

DIRECT VENT PIPE

(Length as required)

Chimney Liner Termination Cap

(Included in Chimney Liner

Termination Kit)

30 ft. (9m) of 3 in. (76mm)

Flex Liner Exhaust Section

(Included in Chimney Liner

Termination Kit)

4 ft. (1m) of 3 in. (76mm)

Flex Liner Air Intake Section

(Included in Chimney Liner

Termination Kit)

Chimney must be sealed

from 4 ft. (1m) section to

termination using a smoke

shelf or a flue restrictor.

Seal should be a minimum of

6 in. (152mm) below end of

4 ft. (1m) Air Intake section.

This section of the

chimney must be sealed

Co-Axial to Co-Linear Connector

(Part 46DVA - GCL)

Alcove Clearance to

Combustibles must be

maintained. See Figure 3.2.

See COAXIAL/COLINEAR

Section and Figure 4.31.

Содержание TOPAZ-MBK-IPI































































Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды

Quadra-Fire TOPAZ-MBK-IPI, Руководство по установке

Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды