Quadra-Fire TOPAZ-MBK-IPI страница 13 Скачать руководство пользователя

Страница: 13 / 62

Quadra-Fire • TOPAZ-MBK-IPI, TOPAZ-D-PMH-IPI, TOPAZ-D-MBK-IPI, TOPAZ-D-CSB-IPI Installation Manual • 2341-980_R10 • 11/15

G. Vent Diagrams

To replace the first 90º starter elbow with two 45º elbows,

refer to Figure 4.7. All other 90º elbows can be replaced

with two 45º elbows.
General Rules:
• SUBTRACT 3 ft. from the total H measurement for each

90º elbow installed horizontally.

• SUBTRACT 1 ft. from the total H measurement for each

45º elbow installed horizontally.

• A maximum of three 90º elbows (or six 45º elbows) may

be used in any vent configuration. Some elbows may be

installed horizontally. See specific vent diagrams.

• When penetrating a combustible wall, a wall shield firestop

must be installed.

• When penetrating a combustible ceiling, a ceiling firestop

must be installed.

Top Vent—Horizontal Termination—Two 45º Elbows
Installation requirements to replace the first 90º elbow

with two 45º elbows:

4 ft min.

(1.22 m)

Figure 4.7

F. Venting Guidelines for Horizontal Runs

Figure 4.6

Max Horizontal Run

20 ft. (6.1 m) when vertical

rise is 10 ft (3m)

Rear Vent with Vertical

Rise

Min of 3 ft vertical (914 mm)

must be used prior to any

horizontal run. Derating ori

fice must be used.

See Figure 4.6.

Horizontal Run requires a non-combustible support

every 5 ft (1.5 m), i.e., plumbing tape

A vent run off the top of the appliance must have a

minimum vertical of 2 feet.

3 FT. MIN.

REAR VENT

CAUTION

VENTING STRAIGHT OUT THE REAR WITHOUT

VERTICAL RISE IS PROHIBITED

All rear vent applications will require the use of a derating

orifice, included in the Rear Vent Kit

Содержание TOPAZ-MBK-IPI































































Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды

Quadra-Fire TOPAZ-MBK-IPI, Руководство по установке

Результаты поиска

Содержание TOPAZ-MBK-IPI

Отзывы:

Похожие инструкции для TOPAZ-MBK-IPI

Бренды по названию

Популярные бренды