Quadra-Fire TOPAZ-MBK-IPI, Руководство по установке

Страница: 10 / 62

Quadra-Fire • TOPAZ-MBK-IPI, TOPAZ-D-PMH-IPI, TOPAZ-D-MBK-IPI, TOPAZ-D-CSB-IPI Installation Manual • 2341-980_R10 • 11/15
10
B. Chimney Diagram
Figure 4.3 Minimum Clearances for Termination
A = 12 inches ................. clearances above grade, veranda,
porch, deck or balcony
B = 12 inches................. clearance to window or door that may
be opened, or to permanently closed
window
C = 18 inches .................clearance below unventilated soffit
18 inches .................clearance below ventilated soffit
30 inches ................. clearance below vinyl soffits and
electrical service
D = 9 inches ................... clearance to outside corner
E = 6 inches ................... clearance to inside corner
F = 3 ft. (Canada) .......... not to be installed above a gas
meter/regulator assembly within 3 feet
horizontally from the center-line of the
regulator
G = 3 ft ........................... clearance to gas service regulator vent
outlet
H = 12 inches................. clearance to non-mechanical
(unpowered) air supply inlet,
combustion air inlet or direct-vent
termination
i = 3 ft. (U.S.A.)
6 ft. (Canada) ........... clearance to a mechanical (powered)
air supply inlet
All mechanical air intakes within 10 feet of a termination cap must
be a minimum of 3 feet below termination.
J = 7 ft. ......................... On public property: clearance above
paved sidewalk or a paved driveway.
A vent shall not terminate directly above a sidewalk or paved
driveway which is located between two single family dwellings and
serves both dwellings.
C
J
B
D
B
F
B
A
E V
V
V
V
V
V
M
H or i
V
G
X
V H
A
V
V
H
X
= AIR SUPPLY INLET
V
= VENT TERMINAL
= AREA WHERE TERMINAL IS NOT PERMITTED
O
N
P
R
Q
Electrical
Service
V
K
V
K
V
L
C
V
Q
MIN
R
MAX
1 cap 3 feet 2 x Q
ACTUAL
2 caps 6 feet 1 x Q
ACTUAL
3 caps 9 feet 2/3 x Q
ACTUAL
4 caps 12 feet 1/2 x Q
ACTUAL
Q
MIN
= # termination caps x 3 R
MAX
= (2 / # termination caps) x Q
ACTUAL
Covered Alcove Applications
(Spaces open only on one side and with an overhang)
N = 6 inches ........... non-vinyl sidewalls
12 inches ......... vinyl sidewalls
O = 18 inches ......... non-vinyl soffit and overhang
42 inches ......... vinyl soffit and overhang
P = 8 ft.
Measure horizontal clearances from this surface.
Measure vertical clearances from this surface.
CAUTION! Risk of Burns! Termination caps are HOT, consider
proximity to doors, traffic areas or where people may pass or
gather (sidewalk, deck, patio, etc.). Listed cap shields available.
Contact your dealer.
• Local codes or regulations may require different clearances.
• Vent system termination is
NOT permitted in screened porches.
• Vent system termination is permitted in porch areas with two or
more sides open.
• Hearth & Home Technologies assumes no responsibility for the
improper performance of the appliance when the venting system
does not meet these requirements.
• Vinyl protection kits are suggested for use with vinyl siding.
M = 18 inches .................... clearance under veranda, porch, deck,
balcony or overhang
42 inches ................ vinyl or composite overhang
Permitted when veranda, porch, deck or balcony is fully open on a
minimum of 2 sides beneath the floor.
K = 6 inches................. clearance from sides of electrical
service
L = 12 inches................ clearance above electrical service
Location of the vent termination must not interfere with access to the
electrical service.