November 28, 2017
7082-151C
7
MT. VERNON E2 INSERT
-C
Model
Mt. Vernon E2 Pellet Insert
Laboratory
OMNI Test Laboratories, Inc.
Report No.
061-S-84-2
Type
Solid Fuel Room Appliance, Pellet Fuel Burn-
ing Type
Standard
ASTM E1509-12, ULC S628-93 and 84-HUD,
Mobile Home Approved.
FCC
Complies with Part 15 of FCC Rules. Opera-
tion is subject to the following two conditions:
(1) this device may not cause harmful inter-
ference, and (2) this device must accept any
interference received, including interference
that may cause undesired operation.
1
Listing and Code Approvals
A. Appliance Certification
NOTE: Hearth & Home Technologies, manufacturer of
this appliance, reserves the right to alter its products, their
specifications and/or price without notice.
NOTICE:
This installation must conform with local codes. In the
absence of local codes you must comply with the
ASTM E1059-
12, ULC S628-93, (UM) 84-HUD and ULC/ORD-C-1482.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualified
installer, service agency or your dealer.
Quadra-Fire is a registered trademark of Hearth & Home
Technologies.
• Installation and use of any damaged appliance.
• Modification of the appliance.
• Installation other than as instructed by Hearth & Home
Technologies.
• Installation and/or use of any component part not approved by
Hearth & Home Technologies.
• Operating appliance without fully assembling all components.
• Operating appliance without legs attached (if supplied with
appliance).
• Do NOT Over fire - If appliance or chimney connector glows,
you are over firing.
Any such action that may cause a fire hazard.
WARNING
Fire Risk.
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided by,
the following actions:
B. BTU & Efficiency Specifications
The Quadra-Fire Mt. Vernon E2 Pellet Insert Appliance
meets the U.S. ENVIRONMENTAL PROTECTION AGENCY
Certified to comply with 2020 particulate emission standards
at 0.74 G/HR EPA CFR subpart AAA, using ASTM E2779-
10, ASTM 2515-11 Method- Pellet Appliance sections, CSA
B415.1-10
. This pellet appliance needs periodic inspection
and repair for proper operation. It is against federal regula-
tions to operate this pellet appliance in a manner inconsistent
with the operating instructions in the owner’s manual.
Emissions Report Number: 0061PS094E
EPA Certification #
98-17
EPA Certified Emissions:
0.74 g/hr
*LHV Tested Efficiency:
83.2%
**HHV Tested Efficiency:
77.9%
***EPA BTU Output: 12,682 - 39,428 / HR
****BTU Input: 16,396 - 50,775 / HR
Vent Size: 3 or 4, “L” or “PL”
Hopper Capacity: 52 lbs.
Fuel Wood Pellets
* Weighted average LHV efficiency using data collected during
EPA emissions test.
**
Weighted average HHV efficiency using data collected during
EPA emissions test.
***
A range of BTU outputs based on HHV and the burn rates
from the low and high EPA tests.
****
Based on the maximum feed rate per hour multiplied by
approximately 8600 BTU’s which is the average BTU’s from a
pound of pellets.
C. Glass Specifications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please con-
tact your dealer for replacement glass.
D. Electrical Rating
115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps
E. Mobile Home Approved
•
This appliance is approved for mobile home installa-
tions when not installed in a sleeping room and when
an outside combustion air inlet is provided.
•
The structural integrity of the mobile home floor, ceil
-
ing, and walls must be maintained.
•
The appliance must be properly grounded to the frame
of the mobile home and use only Listed pellet vent
Class “L” or “PL” connector pipe.
•
Outside Air Kit (OAK-3) must be installed in a mobile
home installation.