Quadra-Fire 4300 Series Скачать руководство пользователя страница 6

Страница: 6 / 36

February 19, 2020

7037-801B

To minimize the effects of negative air pressure:

• Install optional outside air kit with the intake facing

prevailing winds during the heating season

•

Ensure adequate outdoor air for all combustion

appliances and exhaust equipment

• Ensure furnace and air conditioning return vents are

not located in the immediate vicinity of the appliance

• Avoid installing the appliance near doors, walkways or

small isolated spaces

•

Recessed lighting should be a “sealed can” design

• Attic hatches weather stripped or sealed

• Attic mounted duct work and air handler joints and

seams taped or sealed

•

Basement installations should be avoided

D. Tools And Supplies Needed

Before beginning the installation be sure the following tools

and building supplies are available:

- Reciprocating saw

- Framing material

- Pliers

- High temp caulking material

- Hammer

- Gloves

- Phillips screwdriver

- Framing square

Flat blade screwdriver

Electric drill and bits

Plumb line

- Safety glasses

- Level

- Tape measure

- Miscellaneous screws and nails

- 7/16 socket or wrench

1/2-3/4 in. length, #6 or #8 self-drilling screws

• Remove appliance and components from packaging

and inspect for damage.

• Report to your dealer any parts damaged in shipment.

• Read all the instructions before starting the

installation. Follow these instructions carefully

during the installation to ensure maximum safety

and benefit.

E. Inspection of Appliance and Components

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be

voided by, the following actions:

• Installation and use of any damaged appliance.

•

Modification of the appliance.

•

Installation other than as instructed by Hearth &

Home Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

•

Operating appliance without fully assembling

all components.

• Operating appliance without legs attached (if supplied

with appliance).

•

Do NOT Over fire

- If appliance or chimney connector

glows, you are over firing.

Any such action that may cause a fire hazard.

Содержание 4300 Series





































Результаты поиска

Содержание 4300 Series

Отзывы:

Похожие инструкции для 4300 Series

Бренды по названию

Популярные бренды

Quadra-Fire 4300 Series, Руководство по установке

Результаты поиска

Содержание 4300 Series

Отзывы:

Похожие инструкции для 4300 Series

Бренды по названию

Популярные бренды