Quadra-Fire 4300 Series Скачать руководство пользователя страница 15

Страница: 15 / 36

February 19, 2020

7037-801B

C. Clearances to Combustibles

BACKWALL / SIDEWALL

CORNER INSTALLATION

ALCOVE SIDE VIEW

90° OFF TOP UP

& OUT CEILING

CLEARANCE

STOVE TO

CEILING

CLEARANCE

* If H = N/A, follow Pipe

Manufacturer’s clearances

MINIMUM CLEARANCES TO COMBUSTIBLE MATERIALS in inches (Millimeters)

NOTE:

A, C, and F Dimensions are to the center of the ﬂ ue collar

43M-ACC-C AND 43ST-ACC-C WOOD APPLIANCE (2020)

INSTALLATION: FULL VERTICAL OR HORIZONTAL WITH MINIMUM 2 FOOT VERTICAL OFF STOVE TOP

SINGLE WALL PIPE

43M-ACC-C

18-1/2 (470)

11-3/4 (298)

27-1/2 (699)

14-1/2 (368)

8 (203)

20-1/2 (521)

53-1/2 (1359)

12 (305)

43ST-ACC-C

18-1/2 (470)

11-3/4 (298)

27-1/2 (699)

14-1/2 (368)

2-1/2 (64)

15 (381)

49-1/2 (1257)

12 (305)

DOUBLE WALL PIPE

43M-ACC-C

12 (305)

5-1/4 (133)

27-1/2 (699)

14-1/2 (368)

8 (203)

20-1/2 (521)

53-1/2 (1359)

12 (305)

43ST-ACC-C

10-1/2 (267)

3-3/4 (95)

25 (635)

12 (305)

2-1/2 (64)

15 (381)

49-1/2 (1257)

5 (127)

INSTALLATION: 90 DEGREE ELBOW OFF TOP OF APPLIANCE THROUGH BACKWALL

DOUBLE WALL PIPE

43M-ACC-C

11-1/2 (292)

4-3/4 (121)

27-1/2 (699)

14-1/2 (368)

8 (203)

20-1/2 (521)

53-1/2 (1359)

N/A

43ST-ACC-C

10-1/2 (267)

3-3/4 (95)

22 (559)

9 (229)

2-1/2 (64)

15 (381)

49-1/2 (1257)

N/A

INSTALLATION: ALCOVE

DOUBLE WALL PIPE

43M-ACC-C

16 (406)

9-3/8 (238)

27 (686)

13-7/8 (352)

N/A

53-1/2 (1359)

12 (305)

43ST-ACC-C

10-1/2 (267)

3-3/4 (95)

25 (635)

12 (305)

N/A

49-1/2 (1257)

5 (127)

For alcove only:

Six inch diameter listed Double wall air insulated connector pipe with

UL103 HT

listed factory built Class A chimney or masonry chimney. Maximum

depth of Alcove shall be no more than 48 inches (1219mm) and the referenced alcove clearances. Canada must comply with

CAN/ULC-S269 M87

for the 650° factory built

chimney.

* FOLLOW PIPE MANUFACTURES CLEARANCES AS REQUIRED

NOTE:

Clearances may only be reduced by

means approved by the regulatory

authority having jurisdiction

NOTE: Service Space

In order to replace the tube channel assembly a

clearance of 19 inches (483mm) is required on the right

side of appliance in order to remove the tubes with

the appliance in place. If space is not available, the

appliance will have to be disconnected from the chimney

to proceed with the tube replacement.

Fire Risk.

• Comply with all minimum clearances to

combustibles as specified.

•

Failure to comply may cause house fire.

WARNING

ALCOVE TOP VIEW

Содержание 4300 Series





































Результаты поиска

Содержание 4300 Series

Отзывы:

Похожие инструкции для 4300 Series

Бренды по названию

Популярные бренды

Quadra-Fire 4300 Series, Руководство по установке

Результаты поиска

Содержание 4300 Series

Отзывы:

Похожие инструкции для 4300 Series

Бренды по названию

Популярные бренды