quadient DS-200iQ Скачать руководство пользователя страница 199

Страница: 199 / 231

Output Conveyor Troubleshooting

7.5

Output Conveyor Troubleshooting

Suggested Cause and Curative Action

Problem

A. Ensure

Continue

is selected as the Batch mode in

Output Settings. See section

Output Settings

on page

97 for further assistance.
B. Check the DIN lead is properly connected to the Insert
Head.

Conveyor belt does not move.

Move conveyor backstop further away and raise or
lower roller plate to adjust eject angle.

Envelopes bouncing off
backstop with excessive force
on Angled Version.

Fit output rollers in the 2nd position to assist envelope
travel. Contact your local Manufacturer trained
Technical Support Engineer for further assistance).

Envelopes travel untidily
along conveyor on Angled
Version.

Adjust the

Batch complete jog step

in Output Conveyor

Settings. See section

Output Conveyor Settings

on page

100 for further assistance.

Excessive or insufficient gap
between batches when in
batch mode.

Adjust the

Env Conveyor Drive Delay

under the

Miscellaneous category in Unit Fine Tuning screen. See
section

Unit Fine Tuning

on page 140 for further

assistance.

Excessive or insufficient
overlap of envelopes on
conveyor surface.

197

| Page 197 | | May-29-2020 11:33 |

Troubleshooting

Guide

Содержание DS-200iQ








































































































































































































































Результаты поиска

Содержание DS-200iQ

Отзывы:

quadient DS-200iQ, Руководство пользователя, Страница: 199 / 231

Результаты поиска

Содержание DS-200iQ

Отзывы: