quadient DS-200iQ Скачать руководство пользователя страница 196 | Manualshive

Страница: 196 / 231

quadient DS-200iQ Скачать руководство пользователя страница 196

Insert Head Troubleshooting

7.2

Insert Head Troubleshooting

Suggested Cause and Curative Action

Problem

A. Side guides too tight - set to 1mm clearance on each
side.
B. Clean envelope pick-up rollers.

Poor pick-up of envelopes.

A. Separator is set too tight.
B. Clean envelope pick-up rollers.
C. Ensure conveyor cover is fully closed.

Envelope flaps not opening.

Check outer fingers are narrower than the envelope by
9 - 10m on each side but must be wider than the insert.
Reduce the side clearance if necessary. See section

on page 54 for further assistance.

Fingers not inserting properly.

Check side guide clearance - set to 1mm clearance on
each side.

Envelope skewed at insert.

Side guides too tight - set to 1mm clearance on each
side.

Envelopes not arriving at
insert area.

194

| Page 194 | May-29-2020 11:33 |

7

Troubleshooting

Guide

«
...
194
195
196
197
198
...
»

Содержание DS-200iQ








































































































































































































































Отзывы:

Нет отзывов