quadient DS-200iQ Скачать руководство пользователя страница 153

Страница: 153 / 231

Single Cycle 1 x Procedure

Before running a full job, it is advisable to run a single cycle (1x procedure), to establish

whether the tested mailset runs smoothly.

Press the ‘

’ button in the Run Screen as shown below to perform a single cycle

and begin testing the mailset.

Adjustment options for testing the mailset will become available once the single

cycle has been initiated, see section

Testing the Mailset

on page 49 for further

assistance.

Cascading Job

Cascading allows ‘

all available

’ hoppers to be loaded with the same document type.

• Maximum of 2 x adjacent hoppers from Versatile Feeders.

• Maximum of 3 x mark reading hoppers from a Flex Folder.

• Maximum of 4 x non-reading hoppers from a Flex Folder.

The inserting system automatically switches to the next hopper when the current active

(feeding) hopper is empty and vice versa.
As shown below, when a hopper is empty (indicated in yellow), it may be refilled while

the active hopper is running, so the inserting system can keep running without having

to stop for refilling.

Operator

Instructions

151

| Page 151 | May-29-2020 11:33 |

Содержание DS-200iQ








































































































































































































































Результаты поиска

Содержание DS-200iQ

Отзывы:

quadient DS-200iQ, Руководство пользователя, Страница: 153 / 231

Результаты поиска

Содержание DS-200iQ

Отзывы: