quadient DS-200iQ Скачать руководство пользователя страница 144

Страница: 144 / 231

Insert Head Hopper Fine Tuning

Select the Insert Head Hopper document on the Run Screen GUI to open the fine

tuning dialog box options as shown below.

Make any necessary adjustments as required. The available options for fine tuning

the Insert Head hopper document are as follows:

Seal Mode

- Adjusts the seal mode of envelopes.

Select

Off

if manual or later hand insertion is required.

Deskew

- Adjusts the skew of documents.

If skewing occurs, select

Low

if possible, select

High

setting only if necessary.

Wetter Pump On/Off

- Turns the Wetter Pump

Off

Switch pump

for few seconds if wetter tank has dried out - Wetter tank

will automatically refill in normal use.

Press

once the desired settings have been made.

142

| Page 142 | May-29-2020 11:33 |

Operator

Instructions

Содержание DS-200iQ








































































































































































































































Результаты поиска

Содержание DS-200iQ

Отзывы:

quadient DS-200iQ, Руководство пользователя, Страница: 144 / 231

Результаты поиска

Содержание DS-200iQ

Отзывы: